When we that positioning plate and the first step is to compare the cloth have a larger or smaller than the positioning plate, the second step is to locate plate scanning in order to save the files smaller scan pixels to 150 line, the next step after finish scan a size is stitching scans good image splicing I prefer to use the 2006 edition of wilcom feet because it has the navigation and navigation line better than 9.0 9.0 mesh see time is long will dazzle and eye fatigue, the two images together with navigation line made in a horizontal line, the process is more troublesome to do is relatively easy to do.
After the picture is stitched together and then in the periphery of the positioning plate and the positioning plate as large as the contour line after good shaping in the selected line with the offset function to offset 5 mm a line this line and the first line distance is the position of the adhesive.This distance can be based on different goods from the adjustment, the second line is embroidered within the requirements of the positioning board in the embroidery position to play the pattern that customers need, again the statement is when doing sleeves do not tube the shape of the sleeve, the need to embroider the position level so that is to copy for the next step.
Sleeves or before or after the pieces are not embroidered a position, after the first code first completes the size it is good to copy directly and the length of the first code but different pattern of distance and the number of embroidery is the same, after the piece of the positioning plate is bigger but don't worry we fold up the it compromise that was half of us copy this half after scanning in the after is the whole piece of sample.After all the 5 sizes of a position are made, first combine each size for typesetting. After the combination, put the 5 patterns together to align.
After these are operated, click on the automatic start and end function with the digital center point inside the click to determine the point in the lower right corner of the pattern so embroidery work is better done.At this point the whole pattern is done, we are respectively saved to the U disk inside the finished work.The pattern is not difficult I do not know what I said you understand.
In water-soluble embroidery plate making, the bottom of the flat needle step length or short point it is the same final effect, taking into account the current customers are more sensitive to the word "number of needles".So I usually choose to use a relatively long needle step to the bottom needle, about 4 MM.It also has the advantage that you can control where you drop the needle.But in some places that require short stitches, it's a different story.Continuing to lay the base of this petal, I finished it with a 2MM density flat wrapping needle.A density of 2MM is the best, more than that the effect is not obvious, in some wider areas I might use 1.5 density.Water-soluble flower version of the foundation is also very important, it is no less important than the use of plain needles.If the foundation is not enough, after boiling the petals will be very loose and not firm, insufficient fastness.Too much foundation will be too hard, both invisible increase the number of needles, but also affect its post-processing.By post-processing I mean dyeing, and many water-soluble flowers may be dyed.If a place is too hard, the dye is difficult to absorb, appear a little white, directly affect the appearance, now you should know the importance of controlling the amount of foundation.But how to control its thickness is not a word or two words can be clear, this should rely on everyone from long time experience accumulated slowly in practice.There are two methods of laying the bottom, one is the method that we see in the back of the figure of the flat needle and the wrapped needle are used in combination with each other, this method is generally used in the wide width of the place, control the layer number and density of the flat wrapped needle to achieve the purpose, increase the number of layers in the wide place, the density of the dense point.
Now let me tell you how important it is.We know that in the ordinary version, the role of plain stitching is not very obvious, it plays a role is to pave the way, imprisonment.In this case, the purpose of the flat needle is to connect!I put an exclamation point on that word.One way to tell whether a flower is finished or defective after it has been boiled is to see if there are any disjointed spots.When I say "out of touch," I mean something that doesn't connect.We can see where the arrow points in the diagram below.